Turbulent flow inside the cylinder of a Diesel engine — an experimental investigation using hot wire anemometer

This paper describes the measurement of mean velocity and turbulence intensity using hot-wire anemometry inside the cylinder of a Diesel engine under motoring (non-firing) conditions. The effects of engine speed and compression ratio on mean velocity and turbulence intensity have been studied. In addition, turbulence scales have also been evaluated using auto-correlation function and power spectrum which are obtained from fluctuating velocity. The measurements were carried out at 4 different locations inside the piston cavity. Mean velocity and turbulence intensity are found to increase with speed. Increase in compression ratio has significantly increased the mean velocity at all crank angles. The main feature of this investigation is that the experiments have been conducted at higher compression ratios and a relatively high speed using a single high temperature straight wire probe.List of symbols A constant - B constant - D hot-wire diameter - F(f) normalized one-dimensional energy spectral density function - f frequency - i current through the hot-wire - k thermal conductivity of air at any temperature - k ₀ thermal conductivity of air at reference temperature - L hot-wire length - L _t macro or integral time scale of turbulence - L _x macro or integral length scale of turbulence - N number of cycles - Nu Nusselt number - n constant - R hot-wire resistance - Re Reynolds number - R () auto-correlation coefficient - T period of measurement and temperature - T ₀ reference temperature - T _g cylinder gas temperature - T _w hot-wire temperature - U instantaneous velocity - U mean velocity - u _I fluctuating velocity - u turbulence intensity - _t absolute viscosity of air at any temperature - ₀ absolute viscosity of air at reference temperature - engine crank angle - correlation time - _t micro-time scale of turbulence - _x micro-length scale of turbulence     

Point force in a MHB rotating fluid

We consider the steady flow of an inviscid, rotating fluid confined in a cylinder under the influence of a uniform axial magnetic field, in the presence of an isolated point force. It is found that, the wave-like terms, infinite in number, occurring on the downstream side are not persistent and decay at far distances, in contrast to the non-magnetic case. Also the presence of a uniform magnetic field induces an additional finite number of decaying modes on the upstream side and an infinite number of similar modes on the downstream side, which reduce to the geostrophic terms, in the corresponding non-magnetic case. The downstream solution reveals that discontinuities occur in the velocity gradients inside the fluid region.     

Flow boiling heat transfer on a heating element restricted by an interference sleeve

The flow boiling phenomenon over a heated tube restricted by an interference sleeve, which is a passive enhancement technique, has been analysed using a semi-empirical approach. The liquid boiled was water flowing through an annular cross-section. A model developed earlier for the case of pool boiling over porous surfaces has been adapted after modification to pool boiling with interference surfaces using equivalent geometrical parameters and a modified permeability factor. This was further extended to saturated flow boiling situation using an additive mechanism. The single phase heat transfer coefficient required for the additive mechanism is obtained from an experimental correlation developed in the present study. The suppression factors evaluated for the eight sleeve geometries used in the present investigation are expressed in terms of the single phase Reynolds number and the Martinelli parameter. Very good agreement was observed between the model predictions and experimental data validating the mechanisms postulated. Further, a purely empirical correlation based on the present experimental data has been proposed to estimate the two-phase heat transfer coefficient. While the empirical correlation shows a better fit with the experimental data, the additive model has a physical basis.     

Photoelastic studies on progress of separation in interference fits

Interference fits are used extensively in aircraft structural joints because of their improved fatigue performance. Recent advances in analysis of these joints have increased understanding of the nonlinear load-contact and load-interfacial slip variations in these joints. Experimental work in these problems is lacking due to difficulties in determining partial contact and partial slip along the pin-hole interface. In this paper, an experimental procedure is enumerated for determining load-contact relations in interference/clearance fits, using photoelastic models and applying a technique for detecting progress of separation/contact up to predetermined locations. The study incorporates a detailed procedure for model making, controlling interference, locating break of contact up to known locations around the interface, estimating optically the degree of interference, determining interfacial friction and evaluating stresses in the sheet. Experiments, simulating joints in large sheets, were carried out under both pin and plate loads. The present studies provide load-separation behavior in interference joint with finite interfacial friction.     

Convective heat transfer characteristics of microencapsulated phase change material suspensions in minichannels

A comparative experimental study was conducted in order to investigate the convective heat transfer characteristics of water-based suspensions of microencapsulated phase change material (MEPCM) flowing through rectangular copper minichannels. The hydraulic diameter of the channels was 2.71 mm. MEPCM particles with an average size of 4.97 μm were used to form suspensions with mass concentrations ranging from 0 to 20%. The comparative experiments were performed for varying mass flow rates in the laminar region and varying thermal conditions. The cooling performance of the MEPCM suspensions strongly depended on the mass flow rate and the MEPCM mass concentration. The 5% suspension always showed a better cooling performance than water resulting in lower wall temperatures and enhanced heat transfer coefficients within the whole range of mass flow rates. The suspensions with higher mass concentrations, however, were more effective only at low mass flow rates. At higher mass flow rates they showed a less effective cooling performance than water.     

Bending of a uniformly loaded clamped sector plate

The paper involves the expansion of the biharmonic deflection function in a series of non-orthogonal functions satisfying the condition of clamped edges. Each of these non-orthogonal functions is expanded in a series of orthogonal functions which satisfy a certain fourth order differential equation and the boundary conditions implied by the fact that the edges are clamped. This reduces the bending of a uniformly loaded clamped sector plate to the solution of a linear algebraic system of equations. Numerical results for the deflection of the central line are obtained when the semi-sector angle is 15 degrees.     

Facile Synthesis of Novel Pentofuranose Analogs of Phospha Sugar Derivatives

Novel pentofuranose analogs of phospha sugar derivatives were synthesized starting from 1-phenyl-2-phospholene 1-oxide ( 1 ). First, the allylic oxidation of 1-phenyl-2-phospholene 1-oxide ( 1 ) with CrO 3 in Ac 2 O-AcOH or 3-hydroxy-1-phenyl-2-phospholene ( 2 ) with MnO 2 afforded 1-phenyl-4-oxo-2-phospholene 1-oxide ( 3 ). The C-5 alkylation of 3 in the presence of NaH by using benzyl bromide or methyl iodide as electrophiles afforded the target title compounds.     

(S)-(−)-2-Methyl-2-Phenylsuccinic Anhydride,a Novel Resolving Reagent and its Application to Resolution of CIS-5-Amino-4-Phenyl-1,3-DIOXANE

Abstract

A new resolving reagent, (S)-(?)-2-methyl-2-phenylsuccinic anhydride (5) for the resolution of amines via covalent bond formation and its application to the resolution of aminodioxane (±)-(1) is described. The d.e. of the amides (7) and (8) has been determined by studying ¹H-NMR spectra.     

Thermal Behavior of Bismaleimide-Amine/Vinyl Ester Resin-Styrene Blends

Abstract

Curing of 4,4′-bismaleimido-diphenyl methane-4,4′ -diaminodi-phenyl methane (1:0.3 molar ratios) (BM-A) was carried out in the presence of vinyl ester-styrene resin. The BM-A could be cured at lower temperatures. The char yields of the cured resins depended on the percentage of bismaleimide-amine in the blend.